Ranger Valve America

Technical Guide

How do you check the quality of cast steel valve castings?

The short answer

Check four things: the material test reports match the specification, every heat is traceable to the part, the casting is inspected for surface and internal defects, and each finished valve is pressure tested after final machining. A water hydrotest alone can miss pinhole defects, so ask what else the supplier does, such as a submerged gas shell test.

Ranger Valve America Ltd. · Last reviewed

1. Material test reports and traceability

A material test report (MTR) records the chemistry, mechanical properties and heat treatment of the heat the casting came from. Check that it shows tensile and hardness results, chemical composition, heat treatment temperature, holding time and cooling method, and an authorized signature, and that the heat number on the report matches the heat number cast or marked on the part.

Also check the certificate type. An EN 10204 3.1 certificate is issued by the manufacturer and validated by its authorized inspection representative, independent of production. A 3.2 certificate is also validated by an independent inspector, such as the purchaser's representative or a third party.

2. Surface and internal inspection

  • Visual review of the casting surface to MSS SP-55, which grades surface irregularities such as cracks, gas porosity, sand inclusions and excess metal.
  • Magnetic particle testing (MT) or liquid penetrant testing (PT) to find surface and near-surface cracks.
  • Radiography (RT) or ultrasonic testing (UT) to find internal defects such as shrinkage and porosity, where the specification calls for it.
  • Positive material identification (PMI) to confirm that stainless and alloy castings are the grade specified.
  • Dimensional inspection, including wall thickness, which should meet at least the minimum required by ASME B16.34.

3. Pressure testing the finished valve

A shell hydrotest at 150% of rated pressure checks that the body holds pressure. Two questions are worth asking. First, is the test done on the finished valve after final machining, by the valve maker, rather than at the foundry on the raw casting? Second, can the test find pinhole porosity? Liquid can seal a tiny pinhole at test pressure, while gas will pass through it.

That is the reasoning behind the high-pressure pneumatic shell test RANGER-FZV runs on cast steel valves: the completed, uncoated valve is submerged in water and pressure tested with nitrogen or compressed air, and any pinhole shows up as bubbles. RANGER-FZV reports that castings have failed this test after passing a hydrotest.

Questions to ask your valve supplier

  • Do you supply an MTR for each heat, and does it show chemistry, mechanical properties and heat treatment?
  • Is the heat number cast or marked on the part and traceable to that report?
  • What acceptance standard do you apply to casting surfaces?
  • Which castings receive MT or PT, and which receive RT or UT? How is that decided?
  • Is PMI done on every heat of stainless and alloy material?
  • Is each valve shell tested after final machining, and by whom?
  • Are weld repairs permitted, and are they documented against qualified procedures?
  • Can third-party inspectors witness testing and review documentation?

How RANGER-FZV checks its castings

For cast steel gate, globe and check valves, and cast trunnion and floating ball valves, every casting is reviewed against this checklist before it leaves the foundry.

  • 100% Raw Material Certificates Check

    Material certificates are checked for tensile and hardness properties, chemical composition, heat treatment (temperature, holding time, cooling method), and an authorized signature.

  • 10% Dimensional Inspection

    Wall thickness and external dimensions are verified correct.

  • Magnetic Particle Testing

    Standard on one piece from every heat batch.

  • PMI of Every SS and Alloy Heat

    Positive material identification is conducted on all stainless steel and alloy materials.

  • 100% Shell Hydrotest at 150% of Rated Pressure

    A shell hydrotest is conducted per API specification, including pressure and duration.

  • 100% Appearance & Marking Check

    A visual review of casting appearance per MSS SP-55 for cracks, gas porosity, sand inclusions, excess metal, or major repairs, plus a clarity check of all markings.

High-Pressure Pneumatic Shell Test: test pressure by class
ASME classTest pressure (psi)
150300
300575
600725
900725
15002175
25003625
High-Pressure Pneumatic Shell Test: duration by size
NPSDuration (minutes)
1/2" – 4"4
6" – 10"10
12" – 18"20
≥ 20"30

Read the full program on the quality control page. Casting quality snapshots for API 6D and API 600 valves are available from catalogs and manuals.

Frequently asked questions

What is MSS SP-55?

MSS SP-55 is a quality standard for steel castings for valves, flanges and fittings. It gives a visual method for evaluating surface irregularities such as cracks, porosity and inclusions.

What is the difference between a 3.1 and a 3.2 material certificate?

Both are EN 10204 inspection certificates. A 3.1 is validated by the manufacturer's authorized inspection representative, independent of production. A 3.2 is also validated by an independent inspector, such as the purchaser's representative or a third party.

What does PMI do?

Positive material identification checks the chemistry of a finished part, usually with a handheld analyzer, to confirm that stainless and alloy materials are the grade specified.

Why test a valve with gas after a hydrotest?

Gas passes through pinholes and fine porosity that water can seal at test pressure. Submerging the valve and watching for bubbles makes those defects visible.