The short answer
Direct-to-chip liquid cooling typically uses full-port ball valves for isolation at coolant distribution units (CDUs), manifolds and rack branches, butterfly valves on larger headers, check valves at pump discharge, strainers upstream of the CDU and racks, and small ball valves at vents and drains. The valves are normally 316L stainless steel with PTFE or EPDM seals, cleaned to a stated limit, and joined with clamp or orbital-weld ends.
Ranger Valve America Ltd. · Last reviewed
Where each valve goes
Full-port ball valves are the usual choice for isolation, because they add almost no pressure drop. Butterfly valves are normally limited to larger headers, where pressure drop is less critical. Isolation valves at CDUs, manifolds and rack branches let one rack or cooling circuit be serviced without interrupting the others.
| Location | Typical valve | What to look for |
|---|---|---|
| CDU inlet and outlet | Full-port three-piece ball valve | Actuated with position feedback, ISO 5211 mounting pad, serviceable in line |
| Main supply and return headers (DN100 and up) | Butterfly valve or three-piece ball valve | EPDM seat, published Kv, lockable handle |
| Row and branch manifolds | Three-piece or two-piece full-bore ball valve | Full bore, bubble-tight seat |
| Rack branch isolation | Compact two-piece ball valve | Lockable handle, bubble-tight seat, clamp ends |
| Pump discharge | Check valve | Low cracking pressure, non-slam behavior, back-leakage data |
| Upstream of the CDU and racks | Strainer | Mesh to the cold-plate maker's micron rating, differential-pressure ports |
| Vents, drains and sample points | Mini ball valve | Clean thread sealant, capped outlet |
What the valves must do
Compatible wetted materials
Wetted metal parts in 316L stainless steel, with no zinc, brass, copper alloys or lead in the wetted path. PTFE or reinforced PTFE seats and peroxide-cured EPDM elastomers suit deionized water and inhibited propylene glycol. Where a valve offers NBR or silicone as options, confirm that EPDM is what is supplied.
Verified cleanliness
A documented cleaning process (degrease, ultrasonic clean, deionized water rinse, dry), a measurable limit such as particle count, non-volatile residue or an ISO 4406 flush-water code, inspection for oil and fiber, controlled assembly, and capped, bagged packaging. Particles can block cold-plate microchannels.
Stated leak tightness
The seat leakage class and test pressure written down, not just 'zero leakage'. Bubble-tight under ISO 5208 Rate A or API 598 is a stated, testable criterion. Critical locations may also call for a helium leak test with an agreed leak rate.
Low flow resistance
Full-bore ball valves whose bore matches the connecting tube, published Kv values with the test method stated, and a check valve cracking pressure that fits the pump curve. Lower pressure drop means lower pump energy.
Connections that match the piping
Clamp ends or orbital-weld-ready ends in the tube standard the project uses (ASME BPE inch or DIN 11850 metric), with the pressure rating of the clamp joint stated as well as that of the valve.
Continuous operation
Cycle-life test evidence, actuator stroke times slow enough to avoid water hammer, a manual override, lockable handles for lockout / tagout, and a plan for condensation on cold valve bodies and actuators.
What RANGER-FZV supplies and tests
The specifications below are those confirmed in writing by the manufacturer, FZV, for its data center cooling range. Anything shown as on request or custom is not part of standard scope, so ask for it when you enquire.
| Standard supply | On request or custom | |
|---|---|---|
| Body construction | Forged and machined from bar stock; no cast bodies | None |
| Wetted metals | 304, 316 or 316L; all wetted metal parts available in 316L (ASTM A479 316L bar and forgings); no zinc, copper alloys or lead | None |
| Seats and seals | PTFE seats, stem packing and gaskets on ball and check valves; peroxide-cured EPDM on butterfly valves | EPDM on ball valves, check valves and strainers; NBR or silicone on butterfly valves; low-temperature elastomers |
| Pressure testing | 100% of valves: shell test at 1.5 × PN with water for 5 minutes; seat test at 1.1 × PN with dry air for 1 minute each direction, bubble-tight (ISO 5208 Rate A / API 598) | Helium leak test (vacuum method, 1 × 10⁻⁷ mbar·L/s or less); low-pressure air seat test; water hammer test |
| Cleaning | Alkaline ultrasonic degrease, multi-stage deionized water rinse, hot filtered air dry; non-volatile residue of 55 mg/m² or less to ASME BPE; UV inspection of 100% of valves for oil, lubricant and fiber | Particle count or ISO 4406 flush-water analysis |
| Assembly and packaging | Final assembly in a dedicated clean workshop (no formal ISO cleanroom class); end caps, individual sealed bag and carton; clamp gaskets bagged separately | Nitrogen purge inside the bag |
| Flow data | True full bore on ball valves: bore equals the inside diameter of the connecting tube | Kv / Cv (IEC 60534-2-3), pressure drop curves, torque tables, face-to-face dimensions and weights, 3D STEP models |
| Actuation | Electric quarter-turn actuators at 24 V DC, 24 V AC or 230 V AC, 20 to 1000 N·m, IP67, 5 to 15 second stroke with adjustable slow speed, limit switches, manual override, factory-mounted and calibrated | 4–20 mA or Modbus RTU feedback; BACnet; spring-return or supercapacitor fail-safe; IP68 |
| Documents | IOM manual, dimensional drawings, ISO 5208 pressure test certificates, cleaning certificates, batch test reports traceable by heat number; heat number marked on each valve body | EN 10204 3.1 material certificates, PMI reports (standard is sampling), 100% PMI, individual test reports by serial number, CE marking to PED 2014/68/EU, RoHS and REACH declarations |
| Standards | Designed to GB/T 12237 and ASME BPE; production tested to GB/T 26480; manufacturer certified to ISO 9001:2015 | Third-party certification against any of these standards; witnessed factory acceptance testing is accepted |
| Cycle life | Type test of at least 20,000 open-close cycles before seat or stem leakage exceeds ISO 5208 Rate A (a type test, not run on every valve) | Full cycle-life test report |
| Spare parts | Seat and seal kits for all models, 2 to 4 weeks lead time, available for 10 years after the last production run of the model | None |
Questions to ask any liquid cooling valve supplier
- Which seat leakage class and test pressure does 'zero leakage' mean?
- What is the measurable cleanliness limit, and what is the largest particle allowed in the wetted path?
- Can you provide Kv or Cv for every size, and which test method was used?
- For each standard you cite, is the valve designed to it, tested to it, or third-party certified to it?
- Is positive material identification done on every wetted part, or by sample?
- What cycle-life and water hammer test evidence do you have?
- Are the clamp joint and the valve body both rated for the design pressure at the maximum coolant temperature?
- Can you name verified data center or CDU references?
Data center cooling valves from RANGER
See data center cooling valves: three-piece ball valves, two-piece ball valves, butterfly valves, check valves, mini ball valves and strainers. To request Kv data, dimensions or STEP models, send the size list with your quote request.
Frequently asked questions
What material should data center cooling valves be made of?
316L stainless steel is the usual choice for wetted metal parts, with PTFE or EPDM seals. RANGER-FZV's range is forged and bar-machined, with 316L available for all wetted metal parts and no zinc, copper alloys or lead in the wetted path.
Why use ball valves rather than butterfly valves for isolation?
A full-bore ball valve adds almost no pressure drop, which reduces pump energy. Butterfly valves suit larger headers, where pressure drop matters less.
What does bubble-tight mean?
The closed valve is pressurized, usually with air, and no bubbles are visible during the test hold. ISO 5208 Rate A and API 598 bubble-tight both mean no visible leakage over the hold period.
Are RANGER-FZV data center valves third-party certified to ASME BPE?
No. FZV states that the valves are designed to ASME BPE and inspected for dimensions and surface finish, and production tested to GB/T 26480. Third-party certification can be arranged as a special order.
Can the valves be supplied with electric actuators?
Yes, for ball and butterfly valves. Electric quarter-turn actuators are factory-mounted, calibrated and tested with the valve, with a manual override as standard. Check valves and strainers take no actuator.