The short answer
A pressure seal bonnet valve uses the pressure inside the valve to seal the bonnet joint: the bonnet is retained by a split ring and sealed with a gasket-like ring that internal pressure compresses against the body, so the higher the pressure, the tighter the seal. It replaces the large bolted flange of a bolted bonnet valve, which is why the design is preferred for high-pressure, high-temperature service.
Ranger Valve America Ltd. · Last reviewed
What the bonnet joint has to do
The bonnet is the cover on the body of a gate, globe or check valve. The joint between the bonnet and the body has to contain the line pressure and temperature for the life of the valve. Two designs are common: the bolted bonnet and the pressure seal bonnet.
How a pressure seal bonnet works
The bonnet fits inside the body bore, which is why the body has no flange at the top. A sealing ring sits between the bonnet and the body, and a segmented (split) ring holds the bonnet in the body. When the valve is first assembled, the bonnet studs and nuts load the sealing ring to give a starting seal. Once the line is pressurized, the pressure acts on the bonnet and compresses the sealing ring against the body, so the seal gets tighter as the pressure rises.
In RANGER's pressure seal check valve, for example, the parts are the cover, the seal ring, the segment ring, the bonnet, and the studs and nuts.
Pressure seal and bolted bonnet compared
| Bolted bonnet | Pressure seal bonnet | |
|---|---|---|
| What seals the bonnet joint | A gasket compressed between two flanges by the bonnet bolting | A seal ring that internal pressure presses against the body |
| Effect of rising pressure | Pressure works against the bolted joint, so the bolting has to be sized for it | Pressure tightens the seal |
| Body and bonnet at high class | Large flange and bolting | Compact: no body flange |
| Typical use | Wide range of classes and services | High pressure and high temperature service, Class 600 and above |
| Opening the valve | Unbolt the bonnet | Depressurize, then remove the retaining ring and bonnet; fit a new seal ring on reassembly |
| RANGER gate valve | API 600 (see cast steel valves) | 2" – 48", Class 600 – 2500 |
| RANGER globe valve | API 623 (see cast steel valves) | 2" – 24", Class 600 – 2500 |
Where pressure seal valves are used
Pressure seal designs are normally specified for high-pressure, high-temperature isolation, regulation and non-return duties, such as steam and boiler feedwater systems in power plants and high-pressure process lines in refineries. They are normally specified at higher pressure classes: RANGER's pressure seal gate and globe valves start at Class 600, and its API 6D swing check valves use a pressure seal cover as standard in the larger, higher-pressure sizes.
What to specify
- State the pressure class and the design temperature, and ask the supplier to confirm the body and trim materials for that temperature.
- Name the valve type and the standard it follows: API 600 and ASME B16.34 for gate valves, API 623 for globe valves, API 6D for the check valves.
- For erosive service, ask about hard-faced seats and gate or clack.
- If fugitive emissions matter, ask about the stem sealing and any ISO 15848 test.
- Plan for maintenance: the bonnet needs special handling, and the seal ring should be replaced whenever it is removed.
Pressure seal valves from RANGER
RANGER pressure seal parallel slide gate valves run 2" – 48", Class 600 – 2500, designed to the latest applicable revisions of API 600 and ASME B16.34, with hard-faced seat and gate sealing surfaces, a rising stem and a flexible wedge. Pressure seal globe valves run 2" – 24", Class 600 – 2500, with seat and clack faces build-up welded with hard alloy and a choice of clack types for flow adjustment. Pressure seal check valves are standard on 10" and larger at Class 1500 and 8" and larger at Class 2500.
See pressure seal gate valves, pressure seal globe valves and pressure seal check valves.
Frequently asked questions
Why does a pressure seal bonnet seal better as pressure rises?
Internal pressure acts on the bonnet and presses the seal ring against the body. More pressure means more sealing force, which is the opposite of a bolted joint, where pressure tries to open the gasket.
Can a pressure seal bonnet valve be used at low pressure?
It is normally specified at higher classes. At low pressure the seal depends on the initial loading from the bonnet studs, so pressure seal valves are chosen for high-pressure service. RANGER's pressure seal gate and globe valves are Class 600 to 2500.
What is the difference between a pressure seal and a bolted bonnet?
A bolted bonnet is sealed by a gasket squeezed between flanges by bolts. A pressure seal bonnet is sealed by a ring that internal pressure presses against the body, and has no body flange.
Which RANGER valves have a pressure seal bonnet?
Pressure seal parallel slide gate valves, pressure seal globe valves and pressure seal check valves, including the pressure seal cover that is standard on larger, high-pressure API 6D swing check valves.
Request the brochure
The API 6D swing check valve catalogue includes the pressure seal bonnet design, with its parts list, size range and dimensions.
Select what you'd like below and we'll email you secure download links.