Ranger Valve America

Technical Guide

Floating vs trunnion ball valves: what is the difference?

The short answer

In a floating ball valve the ball is held only by the stem and the two seats, so line pressure pushes it against the downstream seat to seal. In a trunnion mounted ball valve the ball is also supported by trunnions at the top and bottom, so it cannot move downstream; spring-loaded seats are pressed onto it by springs and line pressure. Floating valves are simpler and suit smaller sizes and lower classes. Trunnion valves keep operating torque manageable in larger sizes and higher classes.

Ranger Valve America Ltd. · Last reviewed

How a floating ball valve works

In a floating ball valve the ball is not fixed in place: it is held between two seats and driven by the stem. When the valve is closed, line pressure pushes the ball a small distance downstream, so it presses hard against the downstream seat and seals. The harder the pressure pushes, the harder the ball loads that seat.

That is what makes the design simple and economical, and also what limits it. As the size and pressure rise, the force on the downstream seat rises, so operating torque and seat wear rise with it. Floating ball valves are therefore normally used in smaller sizes and lower pressure classes.

How a trunnion mounted ball valve works

A trunnion mounted ball valve fixes the ball with trunnions, upper and lower pins running in bearings. The ball cannot shift downstream, so line pressure does not load the seat through the ball. Instead the seat rings are free to move toward the ball: springs press them on, and line pressure acting on the back of the seat rings forces each one more tightly against the ball.

Because the ball is supported by the trunnions, operating torque stays much lower than for a floating ball of the same size and pressure. That is why trunnion valves are the usual choice for large and high-pressure pipeline service. The seat design also decides how the valve handles body cavity pressure: see DBB vs DIB valves.

Floating and trunnion ball valves compared

Floating ballTrunnion mounted ball
Ball supportHeld by the stem and the two seatsHeld by trunnions (bearings) top and bottom
What presses the seat onto the ballLine pressure pushes the ball into the downstream seatSprings and line pressure press the seat rings onto a fixed ball
Operating torque as size and pressure riseRises quicklyRemains much lower
RANGER body constructionTwo-piece bolted bodyThree-piece body, cast or forged
Cavity pressure and double block and bleedSelf-relieving seat as standard, for automatic internal cavity reliefAll sizes and classes are double block and bleed capable per API 6D; self-relieving, DIB-1 or DIB-2 seat designs are available, depending on service
Typical useGeneral and heavy-duty service in smaller sizes: petroleum, petrochemical, industrialGeneral and severe service, including pipeline, refining and petrochemical
RANGER size1/2" – 10"2" – 56"
RANGER class150 – 600 (cast); 600 – 1500 (forged)150 – 2500

Which one should you specify?

  • Size and class decide most cases. In small bores and lower classes a floating ball valve is compact and economical. As size and class rise, a trunnion valve keeps the torque, and therefore the actuator or gearbox, to a manageable size.
  • Need a double block and bleed arrangement, or a particular seat design (DBB, DIB-1 or DIB-2)? That points to a trunnion valve.
  • Need to repair the valve without removing it from the line? Ask about a top entry trunnion design.
  • Ask the supplier for the operating torque at your maximum differential pressure, for both designs, and for the seat material and its temperature limits.
  • Confirm the fire-safe test (API 607), sour service (NACE MR0175 / ISO 15156) and any SIL requirement in the data sheet.

Floating and trunnion ball valves from RANGER

RANGER two-piece floating ball valves run 1/2" – 10", Class 150 – 600 (cast); 600 – 1500 (forged), with a wide, flexible, self-relieving seat, an O-ring-free body seal design and a blowout-proof stem. RANGER three-piece trunnion ball valves run 2" – 56", Class 150 – 2500, with emergency stem and seat sealant injection on all sizes and classes. Both are designed to API 6D, are fire-safe, and are certified for use in SIL 3 applications.

See floating ball valves, trunnion ball valves, DBB ball valves and top entry ball valves.

Frequently asked questions

What is the difference between a floating ball and a trunnion ball valve?

A floating ball is held by the stem and seats and is pushed into the downstream seat by line pressure. A trunnion ball is also held by trunnions at the top and bottom, so it does not move, and spring-loaded seats press onto it.

Is a trunnion mounted ball valve the same as a fixed ball valve?

Yes. Trunnion mounted and fixed ball are two names for the same design, in which the ball is held in place by trunnions rather than floating.

Why do large floating ball valves need so much torque?

In a floating valve, line pressure pushes the ball into the downstream seat. The force grows with the size of the ball and the pressure, so the seat load and the operating torque grow with it. A trunnion valve takes that load on its bearings instead.

Which type is double block and bleed?

RANGER trunnion mounted ball valves are double block and bleed capable per API 6D in all sizes and classes, with a drain valve for the block-and-bleed function. See the DBB vs DIB guide for how the seat designs differ.

Are RANGER floating and trunnion ball valves fire-safe?

Both are designed to be fire-safe. The floating valve is designed and tested to API 607 and ISO 10497, and the trunnion valve to API 607. See the product pages for the full standards list.

Request the brochure

The API 6D floating ball valve and trunnion mounted ball valve catalogues give the design features, standards, materials and dimensions for each.

Select what you'd like below and we'll email you secure download links.

Catalogue